LL TRADER For iPhone 6 Plus white LCD Display Touch Screen Digitizer G

Replacement screen for any iPhone 6 plus white, which is of the highest quality and all the required tools are included, NOT for iPhone 6s plus.
No touch ID/fingerprint identification function (home button). If you actually need this function,it is very easy to swap the home button if the old one has this function.
Easy for installation by yourself: this part does include the iPhone 6 plus Home Button and the iPhone 6 plus Home Button Ribbon Cable, which means you don't need to transfer them from your old screen onto this new one.
Repair/Replacing old, broken, cracked, damaged faulty LCD Display with touch Screen For iphone 6 plus.
Well packed by "LL TRADER" hard paper box with logo permanently affixed on it as outside packaging.

iPhone 6 Plus LCD Screen and Digitizer Full Assembly - Fix Kit (Top Quality Replacement)

Color: White

Compatibility: This part will only compatible with an iPhone 6 Plus, but not an iPhone 6 , 6s or 6s Plus. Please make sure you identify your iPhone correctly before purchase.

Note:
- This part includes the home button, front facing camera, earpiece speaker, and the LCD shield plate.
- You will not need to transfer these parts from your old display assembly to your new part.
- Important: The Touch ID function will only work with your phone's original home button assembly. You will need to transfer the button assembly from your old display to retain Touch ID.

Package includes:
- 1 x New iPhone 6 Plus LCD Screen and Digitizer
- 2 x Spudger
- 1 x Pentalobe 5-point screwdriver
- 1 x Phillips #000 screwdriver
- 2 x Plastic opening tool
- 1 x Small Suction Cup

Step 1: Power off and disassemble screen.

A. Remove the two 3.6 mm Pentalobe screws next to the Lightning connector.

B. Using a suction cup and plastic opening tool, gently pry the rear case down away from display.

C. Pull the home button end of the front panel assembly away from the rear case, using the top of the phone as a hinge.

D. Open the display to about a 90º angle, and lean it against something to keep it propped up while you're working on the phone.

Note: Don't open the display to over 90º angle or the connectors might be damaged.

Step 2: Disconnect battery cable.

A. Remove the following Phillips screws from the battery connector bracket:

One 2.3 mm screw
One 3.1 mm screw

B. Remove the metal battery connector bracket from the iPhone.

C. Use a plastic opening tool to gently pry the battery connector up from its socket on the logic
board.

Note: Take care to only pry up on the battery connector, and not the socket on the logic board. If you pry up on the logic board socket, you may break the connector entirely.

Step 3: Remove the front panel assembly, and swap the home button if you want to keep the touch ID function.

A. Remove the five Phillips screws securing the front panel assembly cable bracket.

B. Remove the front panel assembly cable bracket from the logic board.

C. Use the flat end of a spudger to disconnect the front-facing camera and sensor cable connecor, home button cable connector, and display cable connector.

D. Remove the front panel assembly from the rear case, and assemble the new screen replacement on your iPhone 6 Plus, then you are good to go.

A. Remove the two 1.8 mm Phillips #00 screws securing the home button bracket to the front panel.

B. Remove the home button bracket from the front panel.

C. Use the point of a spudger to disconnect the home button cable connector by pushing it up and away from the home button.

D. Carefully run the tip of a spudger underneath the perimeter of the home button to separate it from the front panel assembly.

Q: Why my phone works but the screen is not displaying?
A: When reassembling your phone, the display data cable may pop off its connector. This can result in white lines or a blank screen. If that happens, simply reconnect the cable, also disconnect and reconnect the battery connector.

Q: Why the touch function of the screen is not working correctly?
A: This is because the digitizer cable might lose connection if not plugged in firmly, you can transfer the foam that attaches to the back of original digitizer cable connector onto the new one.

50% OFF CLEARANCE